What is the soft side of a metal stud?

Note: Metal studs have roughly a “C” shape. The open side will be referred to as the “soft” side. The side with the webbing will be referred to as the “hard” side.

Which side of a metal stud faces layout?

Soft side of stud faces the layout so you always screw to soft side first. Center studs screw from bottom up so no ones has to hold them. Screw perimeter first and then center studs. As long as the wall your hanging from was framed by you it is plumb so no level is needed.

Which end is up on metal studs?

Inner 10 had it right. Square down so the resilient channel will sit in place. All holes line up. Even though electricians and plumbers usually punch their own holes, it would be like framing a wall and not lining up with the floor joists.

What side of a metal stud do you screw first?

Set screws first at each end of the metal framing track and then every 3 ft. along the track. Overlap track corners by notching the first track’s flange so the overlapping track can slide into place. On long, straight runs, overlap adjoining tracks 6 in.

IT IS INTERESTING:  Frequent question: How do you screw into solid metal?

How do you read a metal stud?

Metal stud manufacturers are required to stamp the stud size and gauge on each product.

Color Guide:

  1. Blue – 118 mils (10-ga)
  2. Red – 97 mils (12-ga)
  3. Orange – 68 mils (14-ga)
  4. Green – 54 mils (16-ga)
  5. Yellow – 43 mils (18-ga)
  6. White – 33 mils (20-ga)
  7. Pink – 30 mils (20-ga; interior only)
  8. Black – 27 mils (22-ga)

Which way should the soft side of the stud face?

Although there is healthy debate among hangers over which they prefer, the soft side of your studs should face the origin of your layout, which is also the starting point of your hanging. All the studs in a wall should face the same way with the exception of floaters and door studs.

How do you hang heavy objects on metal studs?

In order to hang items that need more support, it is possible to drill through metal studs. Titanium or cobalt drill bits are best suited for boring through metal. Once you’ve drilled your pilot holes, you’ll want to use a toggle bolt to safely secure heavy items to the metal stud.

Are metal studs as strong as wood?

For instance, wood studs are stronger than metal studs, and are able to support more weight without being compromised. They are also longer-lasting and easier to cut as well. On the negative side, wood studs are more expensive than steel and can be harder to install, requiring many different tools.

How far apart are metal studs?

Just like wood framing, metal studs should be spaced 16 or 24 inches apart. This allows for the installation of wallboard and other wall sheet products that come in standard sizes. After installing the floor and ceiling tracks, each metal stud is measured, and the length is cut to fit.

IT IS INTERESTING:  How much weight can a steel bolt hold?

Are metal studs load bearing?

Lighter gauge metal studs are used in non-load bearing applications such as some interior walls, half-walls, and partitions. … Metal studs are available in many of the same basic dimensions as wood studs. Metal studs are usually mechanically fastened with screws.

Are metal studs cheaper than wood?

Cost-effective: While never as cheap as wood, steel studs are now only about 30-percent more expensive than wood studs. Lightweight: Steel studs are lighter to carry and store than wood because they are hollow.

What screws are used for metal studs?

Use fine drywall screws to hang drywall on steel studs with a 20- to 25-gauge rating. Use self-drilling drywall screws on 12- to 20-gauge studs. These types of screws have a sharper-than-average tips, with finer threads to deter stripping in metal, plus finer threads grip metal better than standard threads.

How thick is a 20 gauge metal stud?

For example, 20-gauge interior wall partition studs have a thickness of 0.76 mm (30 mil), while 20-gauge structural studs have a minimum thickness of 0.84 mm (33 mil).

How thick are steel wall studs?

The Studco steel stud framing system is manufactured in a range of various widths, lengths and material gauges from 0.50mmBMT to 1.5mm BMT.

What is a flange on a metal stud?

Flange. The Web is the first set of digits supplied in our part number. It is a four digit identifier that translates to the width of the stud in inches. In the example provided, a stud with a 3-5/8″ web is written as 0362.