Frequent question: Can you screw into Hardie board siding?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel.

Can you screw into HardiePlank siding?

James Hardie Building Products recommends keeping nails or screws at least 3/8 inch from the end of a plank. … Drill pilot holes, at each mark, one-quarter to one-half inch deep, to make it easier to insert screws and prevent cracking the siding. Align the bracket holes with the pilot holes in the siding.

What kind of screws do you use for Hardie board?

James Hardie recommends 1-1/4” long galvanized or STAINLESS steel roofing nails or 1-1/4” long ribbed waferhead screws in compliance with the tile industry. It is 8-18 x 3/8” HD.

Is it OK to drill into Hardie board?

It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation. … Otherwise, the board siding may snap during drilling.

IT IS INTERESTING:  Where do you use a flush bolt?

How do you attach things to Hardie board?

Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).

What do you fasten Hardie board with?

Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.

What is the best way to fasten Hardie board?

Fastening Siding

Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.

Can you screw into cement board?

Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place. … Even if you use this extra adhesive, you should still apply the nails or screws.

Is it a bad idea to drill into siding?

You can safely drill into any vinyl sidings if you take a few precautions and follow the correct steps. However, you should avoid doing drilling when the weather is cold as the siding can become brittle. You may want to consider using vinyl siding clips instead of drilling.

IT IS INTERESTING:  Can you screw bolts into wall plugs?

Can you hammer a nail into hardiplank?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. … Use 6d or 8d galvanized or stainless siding nails and install a single nail about 1-in.

Do you need special screws for cement board?

To attach the cement board to the studs, you’ll need special 1-1/4 in. cement board screws (see Fig. B). These screws have a coating to resist corrosion, a special wide head with cutting flutes and hi-low threads for a strong grip. If you can’t find them at a home center, call tile specialty stores.

Are drywall screws OK for cement board?

You don’t want to use regular drywall screws for cement boards. They can corrode, they can break down the edges of the boards, and they won’t drive in flush properly. Use ITW’s ROCK-ON and BACKER-ON screws instead.