In order to hang items that need more support, it is possible to drill through metal studs. Titanium or cobalt drill bits are best suited for boring through metal. Once you’ve drilled your pilot holes, you’ll want to use a toggle bolt to safely secure heavy items to the metal stud.
How do you drill a hole in a metal stud?
Use a small drill bit, or even a finish nail inserted into a drill/driver, to drill holes in the drywall on each side of the stud to pinpoint the edges. It may require punching a few holes to accomplish it — you can patch them later with caulk or even toothpaste. When you find both sides, mark the center of the stud.
Can you drill into a metal frame?
In general, it’s a good idea to drill through metal using as slow a speed as possible using a drill bit for metal. Hard metals like steel and larger drill bits require even slower speeds. With a small twist bit (1/16 in. to 3/16 in.), you can drill through most metals at 3,000 rpm.
Do metal studs have holes?
Metal studs have precut holes designed to accommodate electrical and plumbing lines. When running NM cable through metal framing, inspect the holes to be sure there are no rough or sharp edges that could damage insulation.
What screws to use in metal studs?
Don’t use drywall screws to screw your studs together—they’re not designed for that. Pan-head framing screws work best. Concrete screws work great to attach the bottom track to the floor.
Why can’t I drill into a stud?
The most common reason a drill won’t penetrate a wall at all is because the drill is spinning in the wrong direction. If the drill bit enters the wall and then hits resistance, the typical cause is a metal plate or masonry obstruction.
Is it okay to drill into a stud?
You should not drill or screw deeper than one inch into a stud since electrical wires are typically run through the center of a stud. Another advantage of drilling a pilot hole instead of running a screw straight in is that if you miss the stud a small pilot hole is quicker and easier to repair.
Why can’t I drill through metal?
Drilling into a hard surface requires the use of specialized drill bits. Regular drill bits are not designed to cut through metals. Therefore, they can easily wear away. So you need hard bits which can drill through metals without being damaged.
Can you use drywall screws in metal studs?
Fine-thread drywall screws are self-threading, so they work well for metal studs. Fine-thread drywall screws are best for installing drywall to metal studs. Coarse threads have a tendency to chew through the metal, never gaining proper traction.
Can you build a garage with metal studs?
BUILDING A GARAGE
Metal studs require somewhat different skills and tools, but any general contractor with experience using metal studs should be able to build you a quality garage. Consider using pre-coated aluminum or vinyl siding for the walls of your garage.
How much weight can metal studs hold?
The axial load, or load weight limit, for metal studs varies widely. An 8-foot, 3-1/2-inch metal stud, for instance, may support over 2,000 pounds, while a 16-foot stud of the same width will support as little as 400 pounds.
Do stud finders work on metal studs?
Even though only commercial buildings use metal studs, magnetic stud finders, which are still available, work with wooden studs, too, by locating the metal nails used to mount the wallboard or wooden lath. A newer type of stud finder works by detecting density changes in a wall.
Are metal studs as strong as wood?
For instance, wood studs are stronger than metal studs, and are able to support more weight without being compromised. They are also longer-lasting and easier to cut as well. On the negative side, wood studs are more expensive than steel and can be harder to install, requiring many different tools.
Are metal studs cheaper than wood?
Cost-effective: While never as cheap as wood, steel studs are now only about 30-percent more expensive than wood studs. Lightweight: Steel studs are lighter to carry and store than wood because they are hollow.
How do I know if I have metal studs?
If you think your home might have steel studs, you can check by running a magnet along a wall. While nails and screws in wood studs will attract a magnet, steel studs will have a stronger attraction along the entire height of the stud. An electronic wall stud finder can also detect metal in a wall.