Should I keep shipping bolts?

Once the shipping bolts are removed, it is wise to keep the bolts in a safe place for future use. Shipping bolts can be purchased however, they are very specific to make and model. … The shipping bolts stabilize the drum and drum suspension to prevent damage to the front loading washing machine while being moved.

What happens if I don’t remove transit bolts?

If transit bolts have not been removed, the machine will sense this and refuse to run. It may sound alarm beeps. If there are no such sensors or damages, the motor may force to rotate the drum. This may cause a severe damage, motor burnout, etc.

Can I move a washer without shipping bolts?

It is not recommended that you move front load washers without shipping bolts, and it can damage the machine. … Remove the drain hoses and power cord, wrap the machine with dolly straps, and load it onto a hand truck or dolly for transport.

Why do washing machines have shipping bolts?

Your front-load washing machine came with shipping bolts inserted into the back of the machine. … The shipping bolts keep the tub secure during a move and reduce the amount of vibration that could damage the suspension.

IT IS INTERESTING:  How tight should trailer bolts be?

What happens if you don’t remove shipping bolts from washer?

Failure to remove the shipping bolts and retainers before use may cause severe vibration and noise, which can lead to permanent damage to the washer. The second possible cause of excessive vibration is a shipping block that might be caught under the washer.

Are shipping bolts universal?

Your shipping bolts may come in two different sizes. … Some washers utilize bolts that are uniform in size. These are universal bolts, meaning they will fit in any of the four openings. Use a socket and wrench to tighten your shipping bolts, ensuring they will not be jostled loose during transport.

How important are transit bolts?

Washing machine transit bolts are a vital piece of equipment required to move your washing machine securely. … However, you must remember to remove the transit bolts once your move is complete, as they can seriously damage your machine should you begin a wash cycle with them still in place.

What do transit bolts do?

Transit bolts are a type of bolt used to secure part of a mechanical appliance during transit. … The most common example of transit bolts is the securing of the drum of a washing machine while it is transported from shop to property (or property to property).

Do all new washing machines have transit bolts?

Normally when you get your new washing machine there will be two (rare), three or four transit bolts fitted through the rear panel of the washing machine that fix to the outer tank of the washing machine. … These bolts must be removed before the washing machine is used.

IT IS INTERESTING:  Quick Answer: Is it bad to tighten screws too much?

Is it OK to lay a washing machine on its side?

It’s recommended you always keep a washing machine in an upright position. Laying a washer on its side can cause the inner and outer tubs to bump against each other, which can loosen support pads or damage the suspension. It can also cause the tubs to move out of alignment and alter the way your unit works.

Do top loaders have shipping bolts?

Top-loaders usually require you to wedge foam or cardboard between the drum and the case. For a front-loader, you’ll typically insert shipping bolts in the rear of the washer to secure the drum. If you no longer have the original locks, contact the manufacturer to purchase some.

How do you secure a washing machine drum for transport?

Insert one shipping bolt into each hole and fasten them into place using your wrench or screwdriver. The bolts came with your machine and were removed from these four holes upon installation. With the bolts tightened, your washing machine drum is secure and ready to move.

Do I have to remove transit bolts?

The transit bolts need to be removed when the appliance is being installed. They are designed to hold the drum in a fixed position while being transported. Failure to remove this will void the warranty, so please refer to the appliance manual for additional guidance.

Should washer drum move?

Does the washing machine drum have to move? It is normal for the drum in a new top-loading washing machine to move freely from side to side or front to back.

IT IS INTERESTING:  Do you need to pre drill SPAX screws?