Can I use deck screws for Hardie board?

Can you use deck screws in Hardie board?

The Hardi needs a moisture barrier attached to the studs behind the Hardi, or, waterproofing on the surface of the Hardi but not both. Weight on the wallboard (Hardi) isn’t the issue with using the proper screws. The screws should be alkali resistant, galvanized deck screws don’t qualify.

Can I use deck screws for cement board?

I think the screw will care. I don’t install cement board for a living, but from talking with people/professionals who do, the proper screws should be used. You can’t just use any screw or they will corrode in that application, and Ive seen badly corroded screws from using incorrect ones. Definitely not drywall screws.

Can I use regular screws on Hardie board?

You don’t want to use regular drywall screws for cement boards. They can corrode, they can break down the edges of the boards, and they won’t drive in flush properly. Use ITW’s ROCK-ON and BACKER-ON screws instead.

IT IS INTERESTING:  How do you insulate a wall without studs?

What kind of screws do you use for Hardie board?

James Hardie recommends 1-1/4” long galvanized or STAINLESS steel roofing nails or 1-1/4” long ribbed waferhead screws in compliance with the tile industry. It is 8-18 x 3/8” HD.

Does Hardibacker need special screws?

Fasten HardieBacker cement board with specified nails or screws (as listed in “Materials Required”) every 8 in over the entire surface. Keep fasteners between 3/8 in and 3/4 in from board edges and 2 in from board corners. Prior to setting the tile, fill all joints with the same mortar used to set the tiles.

What kind of screws do you need for cement?

Concrete screws come in 3/16- and 1/4-inch diameter, in lengths up to 3-3/4 inches. Both hex-head and Phillips-head styles are available. They can be used in poured concrete, concrete block, and brick. Expect to pay about $15 for a 100-count box of 1¾-inch-long screws.

Do you need special screws for cement board?

Backer-On Rock-On 1-5/8 in. Cement Board Screws are designed for attaching HardieBacker or equivalent fiber cement backerboard to wood or light gauge steel studs. Backer-On Rock-On’s patented serrated head design countersinks for flush seating at any angle, providing a smooth surface for tile.

Can you use stainless steel screws for cement board?

If your screws were permanently bombarded with moisture then yes stainless would probably the route to take but if there was that much moisture then tanking would be required.

Can I use durock screws on Hardibacker?

Designed for use with HardieBacker® Cement Board and USG Durock® Brand Cement Board, the latest screws feature a premium corrosion resistant finish and help prevent moisture buildup in kitchens and bathrooms.

IT IS INTERESTING:  What are batten screws used for?

What size screws 1/2 inch Hardibacker?

DUROCK Steel Screws, 32 mm (1-1/4) long, are used for applying 12.7 mm (1/2) DUROCK Cement Board to walls or ceilings.

Can you screw into cement board?

Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place. … Even if you use this extra adhesive, you should still apply the nails or screws.

Can you drill holes in hardiplank?

HardiePlank is available as ready-to-paint or with a color layer. Although the siding does not require drilling pilot holes, you may need to run wire or cable through the siding, necessitating drilling a hole.

Can you screw into composite siding?

Fit a cordless drill with a standard wood bit about 1/16 inch larger than the screw if you’re drilling through vinyl or steel siding. Use a carbide or masonry bit if the siding is a composite or concrete-fiber product. … Do not tilt the drill up, down or to either side. Drill only through the exterior siding.